NESA DV Wind Direction sensor 0 ÷ 359°




Catalogue


Datasheet

[contact_popup]
Product Introduction
Product Features
Technical Details
Accessories
Product Introduction

Sensor for measuring wind direction at low power consumption, also available in a heated version (model DVR), compact and sturdy, made of aluminum alloy with anodized to protect against salt air and oxidizing agents. 
Extremely linear and precise, with high dynamic response even in strong winds (up to 300 km/h), easy to interface with any data logger. The sensor uses a special high-precision potentiometer that provides excellent resolution, high sensitivity and a remarkable mechanical durability with an operating angle of 360 °. The sensor is equipped with electrical protections and is available with various signal outputs.

  • High precision Wind Direction Sensor
  • According to WMO standards
  • Compact and light design in aluminium
  • Typical range 0-360°N
  • High dynamic response to wind
  • Suitable for marine applications
  • Available for low temperature applications
  • IP67 fast connection

Product Features

  • Potentiometric measurement of wind direction, precise and linear
  • Instrument according to standard WMO
  • Aluminum sturdy, compact and easy to install
  • Typical measuring range: 0 ÷ 359°
  • Resolution: 0.1°C, accuracy: 1°
  • Sensitivity <0.25 m/s
  • Low power consumption (<0.1 W; <5W@12VDC with heater)
  • High dynamic response to wind
  • Output signal: potentiometer (10K ohm), 0÷2Vdc, 4÷20mA, RS485/Modbus
  • Operating conditions: -30 ÷ +70°C, 0÷80m/s (burst)
  • Power supply: 10 ÷ 30Vdc

Technical Details

Typical measurement range

0 ÷ 360°

Resolution

0.1°

Accuracy

± 1° (sensibility : 0.25m/s thereshold < 0.5m/s )

Type of transducer

Vane with high accuracy potentiometer

Signal output

0÷2Vdc, 4÷20mA , potentiometer 10Kohm, Digital RS485 ModBus

Working conditions

-10 ÷ +70°C; blasts 0 ÷ 80 m/s

 -35 ÷ +70°C heated version

Output resistance

50 ohm for A,B versions

Protections

Polarity reverse and transient

Made of

Anodized aluminum and stainless steel

Power supply and consumption

10 ÷ 28Vdc < 0,1W; 5W@12Vdc with heating

Weight

<460g

Accessories

Standard cable

 

Shielded multi-core cable for indoor/outdoor use, suitable for hot and cold climates.

With IP68 waterproof connector for connecting the sensor, and PS2 plug connector for direct connection to the data logger or with terminal sleeves for insertion into the terminal blocks.

Our cables are standard for most our sensors.

Available in different lengths starting from 1m.

Special Cable

NPI shielded cable. With IP68 waterproof connector for connecting to the sensor, and terminal sleeves for insertion into the terminal blocks.

Available in any length.

Bracket / Arm Support

Fixing system for Nesa’s sensors, composed by an arm of different lengths (50cm, 90cm, 150cm) and thermoplastic resin clam for external, able to withstand to extreme temperature and to solar radiation.

Two stainless steel screws for the tightening of the clamp on the sensor complete the equipment.

MCS Signal Conditioning Module

Single channel module for conditioning digital and analog electrical signals. Fully programmable for binding input/output with the USB interface available as an option.

·       Programmable input signals: Pt100, thermopiles, Voltages up to 2Vdc, Current 0÷20mA or 4÷20mA, frequency up to 1000Hz, Counter for pulses (1ms min)

·       Programmable Output signals: voltage 0÷2Vdc; Current 0÷20mA or 4÷20mA Serial RS485 (command line); Modbus RS485

·       Resolution: 18 bits with over 262,000 points

·       Operating conditions: -40 ÷ +80°C

·       DIN rail mounting

·       Power supply: 10÷30Vdc (typ. 4mA@12 Vdc)